esd electronics, Inc.
HARDWARE  ●  SOFTWARE  ●  ENGINEERING
Ethernet Technologies
SAE J1939 Technologies
Software
SEARCH
Home > Hardware > PMC >
PMC - CPU440

PMC-CPU/440

Item #: V.2027.xx
Availability: Call For Pricing - (413) 772-3170
Usually ships In 2 Weeks


    Choose Your License:
    Choose your license or OS:
    Choose your option:

    Update price

    Not recommended for new design

    PMC-CPU/440

    PowerPC PrPMC Module w/Gigabit Ethernet, USB & CAN

    • PowerPC™ AMCC PPC440EPx
    • 2x 1000 BaseT Ethernet
    • 2…4x CAN interface, TTL level signals
    • 1x RS-232 access via PMC – I/O connector
    • 1x serial console via USB
    • 1x USB host or device
    • 1x IRIG-B time code interface

    PMC PowerPC™ Board

    The PMC-CPU/440 is a PCI Mezzanine Card that automatically switches to monarch (PrPMC) or non-monarch mode according to the system’s requirements. The PowerPC™ AMCC PPC440EPx with 533 MHz or 667 MHz enables a performance of 1334 DMIPS peak, is equipped with at least 256 Mbyte DDR2 RAM and 256 Mbyte NAND Flash, and offers system time support by RTC (with double layer capacitor) or IRIG-B. For CAN bus synchronization tasks, a high-resolution CAN hardware timestamp is supported.

    Connectivity

    The PMC-CPU/440 comes with two Gigabit Ethernet interfaces that are accessible as 1000BaseT via RJ45 connectors at the front panel. The PMC-CPU/440 provides 2...4 CAN interfaces controlled by an FPGA IP-Module. The CAN signals are available as TTL only via PMC connector. External converters from CAN-TTL to CANISO11898 are available. All CAN interfaces allow data transfer rates of 1 Mbit/s. An RS-232 serial port is available via the PMC-I/O connector, too. One USB 2.0 interface (host or device) is available at the front panel.

    Software Support

    The flash memory carries the open source firmware ‘U-Boot’ that enables the PMC-CPU/440 to boot various operating systems from network or on-board Flash, directly and fully supporting Linux, VxWorks (5.5 and 6.3), OS/9 and QNX on-board drivers, as well as supporting higher layer protocols like CANopen and DeviceNet.

    Technical Specifications:

    PMC interface and microprocessor

    Microprocessor

    AMCC PPC440EPx, 533/667 MHz, 32 bit

    Memory

    >256 Mbyte DDR2 RAM, >256 Mbyte NAND flash, >4 Mbyte NOR flash

    RTC

    EPSON RX8025, backup by double layer capacitor

    PCI

    PCI 2.2, 32 bit 33/66 MHz, signal voltage 3.3 V only,

     

    PrPMC acc. to Vita 32, monarch/non-monarch

    Interfaces

    Ethernet

    2x 1000BaseT, IEEE802.3, RJ45-connector

    USB

    USB 2.0 host or device interface at front panel

    Serial

    1x serial console via local USB/serial converter,

     

    1x RS-232 at PMC-I/O connector Pn4 (4-pin)

    CAN

    2...4x CAN, controller FPGA IP module, ISO11898-1 (CAN 2.0), TTL-level signals,

     

    1 Mbit/s, high resolution CAN-hardware timestamp (FPGA), PMC-connector

    IRIG-B

    Digital differential physical layer, IRIG B100 time code format, decoding and time code generation

    General

    Ambient temperature

    TBD

    Humidity

    Max. 90%, non-condensing

    Power supply

    5 V, 3.3 V

    Connectors

    PMC-connector Pn4: CAN, serial, IRIG-B, I²C; front panel –

     

    2x Mini-USB (console, host/device), 2x 1000BaseT

    Order information:

    Designation

     

    Order no.

    PMC-CPU/440

    PrPMC processor AMCC PPC440EPx 533 MHz, 256 MB RAM, 256 MBNAND Flash, 4 MB NOR Flash

    V.2027.02

    PIM-CPU/405

    PIM I/O module (acc. to Vita 36) with 2x CAN ISO11898-2

    V.2025.02

    PMC-CPU/440-VxW

    VxWorks BSP

    V.2027.30

    PMC-CPU/440-Linux

    Linux BSP

    V.2027.32

    PMC-CPU/440-QNX

    QNX BSP

    V.2027.33

    PMC-CPU/440-OS9

    OS/9 BSP

    V.2027.34

     

     

      PMC-CPU/440

      PowerPC PrPMC Module w/Gigabit Ethernet, USB & CAN

      • PowerPC™ AMCC PPC440EPx
      • 2x 1000 BaseT Ethernet
      • 2…4x CAN interface, TTL level signals
      • 1x RS-232 access via PMC – I/O connector
      • 1x serial console via USB
      • 1x USB host or device
      • 1x IRIG-B time code interface

      Documentation




        Phone:413-772-3170 - Fax:413-772-3171 - Web:http://www.esd-electronics-usa.com