|
PMC-CPU/440
PowerPC™ PrPMC Module w/Gigabit Ethernet, USB & CAN
- PowerPC AMCC PPC440EPx, 533/667 MHz, 32 bit
- 2x 1000 BaseT Ethernet
- 2x ... 4x CAN interface
- USB 2.0
- 2x RS-232
- IRIG-B time code interface via PMC-I/O connector
- Linux, VxWorks, QNX and OS9 supported, others on request
- PrPMC monarch or non-monarch
- AMCC PPC440EPx
- 533 MHz, 256 MB RAM, 256 MB NAND Flash, 4 MB NOR Flash
PMC PowerPC™ Board
The PMC-CPU/440 is a PCI Mezzanine Card that automatically switches to monarch (PrPMC) or non-monarch mode according to the system’s requirements. The PowerPCTM AMCC PPC440EPx with 533 MHz or 667 MHz enables a performance of 1334 DMIPS peak, is equipped with at least 256 Mbyte DDR2 RAM and 256 Mbyte NAND Flash, and offers system time support by RTC (with double layer capacitor) or IRIG-B. For CAN bus synchronization tasks, a high-resolution CAN hardware timestamp is supported.
Connectivity
The PMC-CPU/440 comes with two Gigabit Ethernet interfaces that are accessible as 1000BaseT via RJ45 connectors at the front panel. The PMC-CPU/440 provides 2...4 CAN interfaces controlled by an FPGA IP-Module. The CAN signals are available
as TTL only via PMC connector. External converters from CAN-TTL to CANISO11898 are available. All CAN interfaces allow data transfer rates of 1 Mbit/s. An RS-232 serial port is available via the PMC-I/O connector, too. One USB 2.0 interface (host or device) is available at the front panel.
Software Support
The flash memory carries the open source firmware ‘U-Boot’ that enables the PMC-CPU/440 to boot various operating systems from network or on-board Flash, directly and fully supporting Linux, VxWorks (5.5 and 6.3), OS/9 and QNX on-board drivers, as well as supporting higher layer protocols like CANopen and DeviceNet.
Technical Specifications
|
PMC interface and microprocessor
|
|
Microprocessor
|
AMCC PPC440EPx, 533/667 MHz, 32 bit
|
|
Memory
|
>256 Mbyte DDR2 RAM, >256 Mbyte NAND flash, >4
Mbyte NOR flash
|
|
RTC
|
EPSON RX8025, backup by double layer capacitor
|
|
PCI
|
PCI 2.2, 32 bit 33/66 MHz, signal voltage 3.3 V
only,
|
|
PrPMC acc. to Vita 32, monarch/non-monarch
|
|
Interfaces
|
|
Ethernet
|
2x 1000BaseT, IEEE802.3, RJ45-connector
|
|
USB
|
USB 2.0 host or device interface at front panel
|
|
Serial
|
1x serial console via local USB/serial converter,
1x RS-232 at PMC-I/O connector Pn4 (4-pin)
|
|
CAN
|
2...4x CAN, controller FPGA IP module, ISO11898-1
(CAN 2.0), TTL-level signals,
1 Mbit/s, high resolution CAN-hardware timestamp
(FPGA), PMC-connector
|
|
IRIG-B
|
Digital differential physical layer, IRIG B100
time code format, decoding and time code generation
|
|
General
|
|
|
Ambient temperature
|
0 ... 50o C (without forced convection)
|
|
Humidity
|
Max. 90%, non-condensing
|
|
Power supply
|
5 V, 3.3 V
|
|
Connectors
|
PMC-connector Pn4: CAN, serial, IRIG-B, I²C;
Front panel
2x Mini-USB (console, host/device), 2x 1000Base
|
Order information
|
Designation
|
|
order no.
|
|
PMC-CPU/440
|
PrPMC processor AMCC PPC440EPx 533 MHz, 256 MB
RAM, 256 MBNAND Flash, 4 MB NOR Flash
|
V.2027.02
|
|
PIM-CPU/405
|
PIM I/O module (acc. to Vita 36) with 2x CAN
ISO11898-2
|
V.2025.02
|
|
PMC-CPU/440-VxW
|
VxWorks BSP
|
V.2027.30
|
|
PMC-CPU/440-Linux
|
Linux BSP
|
V.2027.32
|
|
PMC-CPU/440-QNX
|
QNX BSP
|
V.2027.33
|
|
PMC-CPU/440-OS9
|
OS/9 BSP
|
V.2027.34 |
|